manualshive.com logo in svg

Siemens SIWAREX WP251, Руководство пользователя

Поделиться
Скачать
Siemens SIWAREX WP251 Скачать руководство пользователя страница 131

 

Scale parameters and functions 

 

8.24 DR 25 Dosing device parameters 

SIWAREX WP251 
Manual, 12/2015, A5E37203357A 

131

 

●

 

The "Activate check stop (1122)" command notifies WP251 to stop again at the next 

check stop point. 

→ The "Check stop follows" bit is set again in the AWI

 Status. 

●

 

The "Continue weighing (1141)" command continues the dosing cycle. 

→ After weighing step 2 is complete, WP251 jumps to "Stopped" state. The "Check stop 

active" bit is set in the AWI Status, and the "Check stop follows" bit is reset. 

●

 

Because no other check stop points were defined, the dosing cycle is performed after 

"Continue weighing (1141)" to the end. 

8.24.12

 

Automatic emptying 

This parameter defines whether and in which form the scale is to be emptied by WP251 at 

the end of an automatic weighing cycle. The following options are available: 

 

Function 

code 

Meaning 

0 (default)  

No emptying. After a tolerance check (if cycle is checked), WP251 completes the 

dosing cycle and jumps to weighing step 0. 

1  

Empty until limit 3 is fallen below. WP251 sets the "Emptying" bit (which can be 

placed directly on one of the digital outputs) until the gross weight falls below limit 3 

(defined in DR 6) and then resets the bit. 

2 

Empty according to specified time. WP251 sets the "Emptying" bit (which can be 

placed directly on one of the digital outputs) based on the emptying time specified in 

DR 25 and then resets the bit automatically – regardless of whether or not the scale 

was completely emptied during the time! 

8.24.13

 

Emptying time 

The parameter defines a fixed time during which the emptying signal is activated in the 

emptying step. It applies only when function code 2 (Emptying according to specified time) is 

selected as the emptying option in DR 25. The setting is made in milliseconds (ms). 

8.24.14

 

Maximum emptying time 

This parameter defines a monitoring time for emptying option 1 in DR 25 (Emptying until limit 

3 is fallen below). The time starts together with the emptying signal. If limit 3 has not yet 

been fallen below after expiration of the time, a corresponding technology message is issued 

that has no further effect on the weighing cycle or emptying. The message is purely 

informative. The parameter setting is made in milliseconds (ms). 

Содержание SIWAREX WP251





























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды