Siemens SIWAREX WP251 Скачать руководство пользователя страница 167

Страница: 167 / 220

Errors and messages

9.6 Operating errors

SIWAREX WP251
Manual, 12/2015, A5E37203357A

167

Technology errors

Error code Description and remedy

2114 Maximum corrective action

exceeded

2114

The corrective active of the controller was greater than

the maximum corrective action configured in DR 24.

2115 Log error

2115

Error while reading a log in DR 46.

2116 Set point too large

2116

The set point specified in DR 20 is greater than the

residual quantity on the scale (removal mode). Weigh-

ing can still be carried out using the "Continue weigh-

ing" and subsequent "Rest emptying" commands!

Reserve

2096 Restore point set

2096

A recovery point was successfully set

2097 Restore point loaded

2097

A recovery point was successfully loaded

2098 Standard parameters

loaded

2098

The standard parameters were successfully loaded

2099 Factory settings loaded

2099

The factory settings were successfully loaded

9.6.3

Data and command errors

Table 9- 2

Data and command errors

Data and command errors Error code Additional

string

Description

5000 Data/command errors 5000

Group error, at least one data/operating error present

6050 Unknown command

6050

Issued command code is unknown. Check the command code.

6051 Command not possi-

ble now

6051

The desired command could not be executed because, for exam-

ple, another process is already active at this time. Additional

information contains details.

4500

, because a fault is present

4501

, because no standstill occurred

4502

, because module is already waiting for standstill

4507

, because dosing active

4514

, because CPU is missing or not ready

4541

, because emptying active

4680

, because SecureDisplay is missing or not visible

4681

, because display command does not match the current display

content

6052 Service command

error

6052

Commands from the Service commands group could not be exe-

cuted. Additional information contains details.

4510

, because service mode is not active

4511

, because write protection active

4507

, because dosing active

4512

, because enable missing

Содержание SIWAREX WP251





























































































































































































































Результаты поиска

Содержание SIWAREX WP251

Отзывы:

Бренды по названию

Популярные бренды

Siemens SIWAREX WP251, Руководство пользователя

Результаты поиска

Содержание SIWAREX WP251

Отзывы:

Бренды по названию

Популярные бренды