manualshive.com logo in svg

Siemens SIWAREX WP251, Руководство пользователя

Поделиться
Скачать
Siemens SIWAREX WP251 Скачать руководство пользователя страница 201

Operation requiring official calibration 

12.2 Verification 

SIWAREX WP251 
Manual, 12/2015, A5E37203357A 

201

 

4. Check of the logbook entries

Only the software downloads for the legal trade display SecureDisplay are retained in the

logbook. It is no longer possible to download the firmware for the SIWAREX WP251

evaluation electronics following verification of the scale with the jumper for write

protection inserted.
– Call up the main menu in the main display (function key with the open-end wrench).

Select the "Calibration check" submenu in the main menu.

– Select the "Logbook check" submenu in the "Calibration check" submenu.
– Navigate in the logbook entries using 4 commands:
– Display first logbook entry
– Display last logbook entry
– Display previous logbook entry
– Display next logbook entry

5. Checking of the ID labels

Checking is carried out in accordance with the specifications in the EC construction

license.

6. Checking of the serial number of the evaluation electronics

The serial number of the evaluation electronics used (shown at top right in the

SecureDisplay) must agree with the ID label. The serial number of the evaluation

electronics used can also be called on the SecureDisplay.
– Call up the main menu in the main display (function key with the open-end wrench).

Select the "Calibration check" submenu in the main menu.

– Select the "Version and variables check" submenu in the "Calibration check"

submenu.

– Activate the "Display SIWAREX serial number" command.
– The current serial number is then shown on the display.

7. Checking of the regulation code

Check whether the regulation code "OIML" is set in the scale parameters. The code can

be called on the SecureDisplay.
– Call up the main menu in the main display (function key with the open-end wrench).

Select the "Calibration check" submenu in the main menu.

– Select the "Version and variables check" submenu in the "Calibration check"

submenu.

– Activate the "Display calibration regulation" command.
– The currently set code is then shown on the display.

Содержание SIWAREX WP251





























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды