Seagate Exos E 4U106 Скачать руководство пользователя страница 66

Страница: 66 / 102

Installation

Connecting power cords to the PSU

IMPORTANT:

The 4U106 enclosure is fitted with two redundant PSUs. Both power cords must be connected to at least

two separate and independent power supplies to ensure redundancy.

•

Figure 58

shows power connection from a single-core PSU to a PDU using C19 connectors. For the sake of simplicity,

we have shown power cables connections without the use of CMA and its brackets.

•

The C20 plug on the PSU connects to the C19 receptacle of the power cord. The C20 plug on the power cord connects
to the C19 receptacle in the PDU.

CAUTION:

Power connection concerns:

•

Never connect the power cord to the PSU before installing the PSU in the system.

•

Always remove the power connections

before

you remove the PSU from the enclosure.

•

Whether standard (single-lead) or bifurcated (Y-lead), power cords must only be connected to a supply range of
200–240VAC as indicated on each PSU’s hazardous voltage warning label.

Figure 58 AC power cord connection from PDU to PSU (simplified view)

Figure 59 Actual photo of enclosure Cables routed through CMA

Power Distribution Units (AC UPS shown)

C14

C19

C14

C19

Содержание Exos E 4U106







































































































Результаты поиска

Содержание Exos E 4U106

Отзывы:

Похожие инструкции для Exos E 4U106

Бренды по названию

Популярные бренды

Seagate Exos E 4U106, Руководство по установке и обслуживанию оборудования

Результаты поиска

Содержание Exos E 4U106

Отзывы:

Похожие инструкции для Exos E 4U106

Бренды по названию

Популярные бренды