Seagate Exos E 4U106 Скачать руководство пользователя страница 96 | Manualshive

Страница: 96 / 102

background image

96

Standards and regulations

B

Standards and regulations

International standards

The enclosure system complies with the requirements of the following agencies and latest editions of the following
standards:

•

CE to EN 60950-1

•

CB report to IEC 60950-1

•

UL & cUL to UL 60950-1

Potential for radio frequency interference

USA Federal Communications Commission (FCC)

Notice

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the
FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case
the user will be required to correct the interference at his or her expense.

Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. The supplier
is not responsible for any radio or television interference caused by using other than recommended cables and
connectors or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could
void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.

European regulations

This equipment complies with European Regulations EN 55032 Class A: Limits and Methods of Measurement of Radio
Disturbance Characteristics of Information Technology Equipment and EN50082-1: Generic Immunity.

Safety compliance

Table 13

Safety compliance specifications

System product type approval

UL/cUL/CE

Safety compliance

UL 60950-1

CAN/CSA-C22.2 No. 60950-1-07

EN 60950-1

IEC 60950-1

CCC (China PRC - CCC Power Supplies)

BIS (India - BIS PSU and system)

«
...
94
95
96
97
98
...
»

Содержание Exos E 4U106







































































































Отзывы:

Нет отзывов

Похожие инструкции для Exos E 4U106

Бренд: Hammer Страницы: 6

Бренд: Stardom Страницы: 14

Бренд: Airlink101 Страницы: 5

Бренд: Focal Страницы: 23

ALUPRES-EX Series

Бренд: Palazzoli Страницы: 12

EC-3US25 SuperSpeed

Бренд: Sabrent Страницы: 2

Port 6Gb/s 3.5"

Бренд: In Win Страницы: 9

Quickstore Portable

Бренд: Sharkoon Страницы: 9

Бренд: Rosewill Страницы: 1

Бренд: Center Страницы: 11

Бренд: Icy Box Страницы: 8

Бренд: Icy Box Страницы: 12

Бренд: Alto Страницы: 14

Бренд: D.A.S. Страницы: 24

Бренд: ZALMAN Страницы: 20

Бренд: Sabrent Страницы: 17

Бренд: LaCie Страницы: 41

Бренд: GAMEMAX Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды