Seagate Exos E 4U106 Скачать руководство пользователя страница 94

Страница: 94 / 102

Technical specifications

Environmental requirements

Power supply unit specifications

Table 11

Ambient temperature and humidity

Specification

Temperature range

Relative humidity

Operating

5ºC to 35ºC (41ºF to 95ºF, derated by 1ºC per 300m above
900m) (ASHRAE A2 2015 thermal guidelines)

-12ºC DP/10 to 80% (Max)
(Non-condensing)

Non-operating

-40ºC to +70ºC (-40ºF to +158ºF) (Max rate of change: 20ºC)

-12ºC DP/5 to 100% (Max)
(Non-condensing)

Specification

Measurement/description

Airflow

System must be operated with low pressure rear exhaust installation.
Back pressure created by rack doors and obstacles not to exceed 5Pa (0.5 mm H

Altitude, operating

-100 to 3,048 meters (-328 to 10,000 feet). Maximum operating temperature is derated
by 1ºC for each 300 m above 900 m (2952.76 feet)

Altitude, non-operating

-100 to 12,192 m (-328 to 40,000 feet)

Shock, operating

3.0 g, 11 ms (per axis)

Shock, non-operating

20.0 g, 7ms, 10 shock pulses (2 shocks per axis X, Y in positive and negative direction,
and 2 shocks in positive Z axis) OR ISTA 3H (mounted in a rack, horizontal impact on
all sides, 4-in drop tests)

Vibration, operating

0.18G

rms

5 Hz to 500 Hz, 30 min per axis

Vibration, non-operating

0.54 G

rms

6Hz to 200 Hz (ISTA 3E)

Vibration, relocation

ISTA3H air ride for 60 min

Acoustics

4U enclosures: Sound power operating



8.5 Bels LW

@ 23ºC

Orientation and mounting: 1.2 m rack mount (4 EIA units)

•

Rack rails

To fit 1.2 m depth racks compliant with the SSI server rack specification

•

Rack characteristics

Back pressure not exceeding 5Pa (~0.5 mm H

Table 12

Power supply unit module specifications

Specification

Measurement/description

Dimensions (size)

38.1 mm high x 169.9 mm wide x 211.1 mm long:

•

X-axis length: 169.9 mm (6.69 in)

•

Y-axis length: 38.1 mm (1.5 in)

•

Z-axis length: 211.1 mm (8.3 in)

Maximum output power

2000 W

Voltage range

200–240 VAC rated

Frequency

50–60 Hz

Voltage range selection

Auto-ranging: 90–264 VAC, 47–63 Hz

Maximum inrush current

55A

Power conversion efficiency



94% @ 230 VAC (50% load)

Harmonics

Meets EN61000-3-2 (EU), EN 31000-3-3 (EU), EN 55024 (EU), KN 24/KN 35 (S. Korea)

Output

+12V @ 164A, +12V Standby Voltage @ 3.5A, 5V for circuit operation

Содержание Exos E 4U106







































































































Результаты поиска

Содержание Exos E 4U106

Отзывы:

Похожие инструкции для Exos E 4U106

Бренды по названию

Популярные бренды

Seagate Exos E 4U106, Руководство по установке и обслуживанию оборудования

Результаты поиска

Содержание Exos E 4U106

Отзывы:

Похожие инструкции для Exos E 4U106

Бренды по названию

Популярные бренды