Scientific SMO1000A-S Скачать руководство пользователя страница 16

Страница: 16 / 176

User Manual SMO1000A-S

16/176

General Inspection

Inspect the shipping container for damage.

Keep the damaged shipping container or cushioning material until the contents of the

shipment have been checked for completeness and the instrument has passed both

electrical and mechanical tests.

The consigner or carrier shall be liable for the damage to instrument resulting from

shipment. The manufacturer would not be responsible for free maintenance/rework or

replacement of the unit.

Inspect the instrument.

In case of any damage, or defect, or failure, notify your sales representative.

Check the Accessories

Please check the accessories according to the packing lists. If the accessories are

incomplete or damaged, please contact your sales representative.

Содержание SMO1000A-S

















































































































































































Результаты поиска

Содержание SMO1000A-S

Отзывы:

Похожие инструкции для SMO1000A-S

Бренды по названию

Популярные бренды

Scientific SMO1000A-S, Руководство пользователя

Результаты поиска

Содержание SMO1000A-S

Отзывы:

Похожие инструкции для SMO1000A-S

Бренды по названию

Популярные бренды