Scientific SMO1000A-S Скачать руководство пользователя страница 107

Страница: 107 / 176

User Manual SMO1000A-S

107/176

Math Operators

The oscilloscope supports math count operation (Addition, subtraction, multiplication,

division), FFT (Fourier transform) operation and math function operation (differential,

integral, square root).

Addition or Subtraction

Math operators perform arithmetic operations add or subtract operation on any two analog

input channels. When you select addition or subtraction, the

Source A

and

Source B

values are added or subtracted point by point, and the result is displayed.

Press the

Math

button on the front panel to enter the MATH function menu.

Press the

Source A

and

Source B

softkey respectively, and then turn the

Universal

Knob

to select the source to do math operation. Analog channels (CH1 and CH2) and

reference waveforms (REFA and REFB) can be used as Source A or source B.

Press the

Operation

softkey and then turn the universal to select

to make

addition or subtraction operation. The resulting math waveform is displayed in white

and labeled with

―

If you want to invert the math waveform, press the

Invert

button and set the option to

to invert the display of the math waveform.

Содержание SMO1000A-S

















































































































































































Результаты поиска

Содержание SMO1000A-S

Отзывы:

Похожие инструкции для SMO1000A-S

Бренды по названию

Популярные бренды

Scientific SMO1000A-S, Руководство пользователя

Результаты поиска

Содержание SMO1000A-S

Отзывы:

Похожие инструкции для SMO1000A-S

Бренды по названию

Популярные бренды