Scientific SMO1000A-S Скачать руководство пользователя страница 176

Страница: 176 / 176

User Manual SMO1000A-S

176/176

Service and Support

No user serviceable parts are inside the instrument, should it become

necessary to send back the instrument to factory for service, please

observe the following procedure.

Before dispatching the instrument please write to us giving full details of

the fault noticed, model number and serial number.

After receipt of your letter our service department will advise you whether

it is necessary to send the instrument back to us for repairs or the

adjustment is possible in your premises.

Dispatch the instrument to us (only on the receipt of our advice) at our

factory address, securely packed in original packing, duly insured and

freight paid along with accessories and a copy of the fault details noticed.

Содержание SMO1000A-S

















































































































































































Результаты поиска

Содержание SMO1000A-S

Отзывы:

Похожие инструкции для SMO1000A-S

Бренды по названию

Популярные бренды

Scientific SMO1000A-S, Руководство пользователя

Результаты поиска

Содержание SMO1000A-S

Отзывы:

Похожие инструкции для SMO1000A-S

Бренды по названию

Популярные бренды