Scientific SMO1000A-S Скачать руководство пользователя страница 154

Страница: 154 / 176

User Manual SMO1000A-S

154/176

Do Self Test

Self tests include screen test, keyboard test, and LED test. Self tests used to test the

screen, buttons, knobs and LED lights whether works well.

Screen Test

Press the

Utility

button on the front panel to enter the UTILITY function menu.

Press the

Next Page

softkey to go to the second page of the UTILITY function menu.

Press the

Next Page

softkey to go to the third page of the UTILITY function menu.

Press the

Do Self Test

softkey to enter the SELFTEST function menu.

Press the

Screen Test

softkey to enter the screen test interface, as the picture shown

below, the screen display pure red.

Figure 81 Screen Test

Press the

Single

button on the front panel continually as it says in the picture above.

The screen displays green, blue and red again. It is easy to check chromatic

aberration, stain and scratch of the screen under the condition.

Press the

Run/Stop

button on the front panel to exit the screen test program.

Содержание SMO1000A-S

















































































































































































Результаты поиска

Содержание SMO1000A-S

Отзывы:

Похожие инструкции для SMO1000A-S

Бренды по названию

Популярные бренды

Scientific SMO1000A-S, Руководство пользователя

Результаты поиска

Содержание SMO1000A-S

Отзывы:

Похожие инструкции для SMO1000A-S

Бренды по названию

Популярные бренды