Scientific SMO1000A-S Скачать руководство пользователя страница 153

Страница: 153 / 176

User Manual SMO1000A-S

153/176

To Update Firmware and Configuration

The firmware and configuration can be updated directly via USB flash driver.

Do the following steps to update the firmware:

Insert the USB flash driver which with the firmware and the configure files inside into

the USB host interface on the front panel of the oscilloscope.

Press the

Utility

button on the front panel to enter the UTILITY function menu.

Press the

Next Page

softkey to go to the second page of the UTILITY function menu.

Press the

Next Page

softkey to go to the third page of the UTILITY function menu.

Press the

Update

softkey to enter the UPDATE function menu.

Press the

Firmware

softkey and it will pop-out the message “

Press ‘Single’ to

continue and press ‘Run/Stop’ to exit!”

Press the

Single

button to enter the SAVE/RECALL file system.

Turn the

Universal Knob

to select the update file which should be with an ADS postfix;

and then press the

Load

softkey to start update the firmware. The process needs

about 7 minutes. And during the update, do not cut off the oscilloscope, otherwise the

oscilloscope will not restart again.

After finish the update, the screen will pop-out the message “

Update success, please

restart the DSO

”, and you will heard a sound of buzzer.

10. Restart the oscilloscope to finish the firmware update.

Do the following steps to update the configuration:

Insert the USB flash driver which with the firmware and the configure files inside into

the USB host interface on the front panel of the oscilloscope.

Press the

Utility

button on the front panel to enter the UTILITY function menu.

Press the

Next Page

softkey to go to the second page of the UTILITY function menu.

Press the

Next Page

softkey to go to the third page of the UTILITY function menu.

Press the

Update

softkey to enter the UPDATE function menu.

Press the

Configure

softkey to enter the SAVE/RECALL file system.

Turn the

Universal Knob

to select the update file which should be with an CFG

postfix; and then press the

Load

softkey to start update the firmware. The process

needs about 30 seconds.

After finish the update, the screen will pop-out the message “

Update success, please

restart the DSO

”, and you will heard a sound of buzzer.

Restart the oscilloscope to finish the configuration update.

Содержание SMO1000A-S

















































































































































































Результаты поиска

Содержание SMO1000A-S

Отзывы:

Похожие инструкции для SMO1000A-S

Бренды по названию

Популярные бренды

Scientific SMO1000A-S, Руководство пользователя

Результаты поиска

Содержание SMO1000A-S

Отзывы:

Похожие инструкции для SMO1000A-S

Бренды по названию

Популярные бренды