Scientific SMO1000A-S Скачать руководство пользователя страница 104

Страница: 104 / 176

User Manual SMO1000A-S

104/176

To Save REF Waveform to Internal Memory

Do the following steps to save the REF waveform to internal memory:

Press the

REF

button on the front to enter the REF WAVE function menu. Note that

when the time horizontal format is in X-Y mode, REF function cannot be enabled.

Press the

Source

softkey; then, turn the

Universal Knob

to select the source of

reference channel. The source includes analog channel and math waveforms.

Press the

Location

softkey; then, turn the

Universal Knob

to select the position to

save the REF waveform. The source includes analog channel and math waveforms.

Press the

Save

softkey to save the channel or math waveform to the appointed

location. The vertical scale information and the vertical offset of the waveform will be

saved at the same time. It will pop out the message

―

Store Data Success

when the

waveform has been saved successfully.

To Display REF Waveform

To the following steps to display REF waveform:

Press the

REF

button on the front to enter the REF WAVE function menu.

Press the

Location

softkey; then, turn the

Universal Knob

to select the REF

waveform that you want to display.

Press the

Display

softkey to select

to display the REF waveform on the screen.

Only saved location can be displayed. The oscilloscope can display all four reference

waveforms at a time.

Note: The REF waveforms are non-volatile. The REF waveform can still be saved
after restarts or default operation.

Содержание SMO1000A-S

















































































































































































Результаты поиска

Содержание SMO1000A-S

Отзывы:

Похожие инструкции для SMO1000A-S

Бренды по названию

Популярные бренды

Scientific SMO1000A-S, Руководство пользователя

Результаты поиска

Содержание SMO1000A-S

Отзывы:

Похожие инструкции для SMO1000A-S

Бренды по названию

Популярные бренды