Scientific SMO1000A-S Скачать руководство пользователя страница 28

Страница: 28 / 176

User Manual SMO1000A-S

28/176

Universal Knob

Adjust the waveform intensity.

When there is no menu operation, turn the knob to adjust the intensity of the displayed

waveforms. The adjustable range is from 0% to 100%. Turn clockwise to increase the

intensity and counterclockwise to reduce. You can also press the

Display/Persist

button; press the

Next Page

softkey to go to the second page of the DISPLAY

function menu; press the

Intensity

softkey and then turn the

Universal Knob

adjust the waveform intensity.

Select the desired submenu.

In menu operation, press any menu softkey and turn the

Universal Knob

to select the

desired submenu under the menu and push down the knob to confirm the current

submenu. Turn clockwise to up the intensity and counterclockwise to down.

Modify parameters.

After having chosen a parameter, turn the

Universal Knob

to modify the value. Turn

clockwise to increase the intensity and counterclockwise to reduce. In addition, it can

also be used to adjust scale and offset of MATH and REF.

Choose file or directory or input filename.

After having entered the file system, turn the

Universal Knob

to select the desired file

or directory. When inputting filename, turn the

Universal Knob

to select the desired

character and the push the knob to confirm.

Содержание SMO1000A-S

















































































































































































Результаты поиска

Содержание SMO1000A-S

Отзывы:

Похожие инструкции для SMO1000A-S

Бренды по названию

Популярные бренды

Scientific SMO1000A-S, Руководство пользователя

Результаты поиска

Содержание SMO1000A-S

Отзывы:

Похожие инструкции для SMO1000A-S

Бренды по названию

Популярные бренды