Scientific SMO1000A-S Скачать руководство пользователя страница 13

Страница: 13 / 176

User Manual SMO1000A-S

13/176

Installation (overvoltage) Category

This product is powered by mains conforming to installation (overvoltage) category II.

WARNING

Make sure that no overvoltage (such as that caused by thunderbolt) can reach

the product, or else the operator might expose to danger of electric shock.

Installation (overvoltage) Category Definitions

Installation (overvoltage) category I refers to signal level which is applicable to equipment

measurement terminals connected to the source circuit. In these terminals, precautions

are done to limit the transient voltage to the corresponding low level.

Installation (overvoltage) category II refers to the local power distribution level which is

applicable to equipment connected to the AC line (AC power).

This oscilloscope uses fan to force cooling. Please make sure that the air intake and

exhaust areas are free from obstructions and have free air. When using the oscilloscope in

a bench-top or rack setting, provide at least 10 cm clearance beside, above and behind the

instrument for adequate ventilation.

WARNING

Inadequate ventilation may cause temperature increase which would damage

the instrument. So please keep the instrument well ventilated during operation

and inspect the intake and fan regularly.

Care

Do not store or leave the instrument in direct sunshine for long periods of time.

WARNING

To avoid damages to the instrument or probe, please do not leave them in fog,

liquid, or solvent.

Cleaning

Please perform the following steps to clean the instrument and probe regularly according

to its operating conditions.

Disconnect the instrument from all power sources, and then clean it with a soft

wet cloth.

Clean the loose dust on the outside of the instrument and probe with a soft cloth.

When cleaning the LCD, take care to avoid scarifying it.

WARNING

To avoid damages to the surface of the instrument and probe, please do

not use any corrosive liquid or chemical cleanser. Make sure that the

instrument is completely dry before restarting it to avoid short circuits or

personal injuries.

Содержание SMO1000A-S

















































































































































































Результаты поиска

Содержание SMO1000A-S

Отзывы:

Похожие инструкции для SMO1000A-S

Бренды по названию

Популярные бренды

Scientific SMO1000A-S, Руководство пользователя

Результаты поиска

Содержание SMO1000A-S

Отзывы:

Похожие инструкции для SMO1000A-S

Бренды по названию

Популярные бренды