Scientific SMO1000A-S Скачать руководство пользователя страница 105

Страница: 105 / 176

User Manual SMO1000A-S

105/176

To Adjust REF Waveform Display

Please refer to the

―

To Display REF Waveform

above to display the desired

reference waveform.

Press the

Scale

and

Position

softkey and turn the

universal

knob to adjust the vertical

scale and position of the reference waveform. The vertical scale and position

information display at the middle of the screen.

The initial values display at the middle of the screen is the setup that when the reference

waveform been saved.

Figure 53 Reference Waveform

To Clear REF Waveform Display

The oscilloscope does not have the

―

Clear

option under the REF WAVE function menu.

To clear the appointed reference waveform, you can save a new reference waveform to

the same location to cover it.

Note: The vertical Variable knob and the vertical Position knob are only works for

the reference waveform and the math waveform. Please make a difference with the

channel vertical system.

Содержание SMO1000A-S

















































































































































































Результаты поиска

Содержание SMO1000A-S

Отзывы:

Похожие инструкции для SMO1000A-S

Бренды по названию

Популярные бренды

Scientific SMO1000A-S, Руководство пользователя

Результаты поиска

Содержание SMO1000A-S

Отзывы:

Похожие инструкции для SMO1000A-S

Бренды по названию

Популярные бренды