Scientific SMO1000A-S Скачать руководство пользователя страница 69

Страница: 69 / 176

User Manual SMO1000A-S

69/176

Pulse Trigger

Trigger on the positive or negative pulse with a specified width.

Press the

Setup

button on the front panel to enter the TRIGGER function menu.

Press the

Type

softkey; turn the

Universal Knob

to select

Pulse

and then push the

knob to confirm.

Press the

Source

softkey; turn the

Universal Knob

to select CH1 or CH2 as the

trigger source.

Turn the

Trigger Level Knob

to adjust the trigger level to the desired place.

Press the

Polarity

softkey to select

Positive

Negative

pulse that to trigger on. The

current trigger polarity is displayed at the upper right corner of the screen.

Press the

Limit Range

softkey; turn the

Universal Knob

to select the desired

condition.

(less than a time value): trigger when the positive or negative pulse time of the

input signal is lower than the specified time value.

For example, for a positive pulse, if you set t (pulse real width) < 100ns, the

waveform will trigger.

(greater than a time value): trigger when the positive or negative pulse time of

the input signal is greater than the specified time value.

For example, for a positive pulse, if you set t (pulse real width) >100ns, the

waveform will trigger.

Содержание SMO1000A-S

















































































































































































Результаты поиска

Содержание SMO1000A-S

Отзывы:

Похожие инструкции для SMO1000A-S

Бренды по названию

Популярные бренды

Scientific SMO1000A-S, Руководство пользователя

Результаты поиска

Содержание SMO1000A-S

Отзывы:

Похожие инструкции для SMO1000A-S

Бренды по названию

Популярные бренды