Scientific SMO1000A-S Скачать руководство пользователя страница 35

Страница: 35 / 176

User Manual SMO1000A-S

35/176

To Enable the Channel

The oscilloscope provides 2 analog input channels (CH1, CH2) and provides independent

vertical control system for each channel. As the vertical system setting methods of both

channels are the same, this chapter takes CH1 as an example to introduce the setting

method of the vertical system.

Connect a signal to the CH1 channel connector; and then press the

CH1

button in the

vertical control area (VERTICAL) at the front panel to enable CH1.

The channel setting menu is displayed at the bottom of the screen and the channel label

at the right side of the screen. The information displayed in the channel label is related to

the current channel setting.

After the channel is turned on, modify the parameters such as the vertical scale, the

horizontal time base and the trigger mode according to the input signal to make the

waveform display easy to observe and measure.

Note: to turn off the channel, press the channel button twice.

Содержание SMO1000A-S

















































































































































































Результаты поиска

Содержание SMO1000A-S

Отзывы:

Похожие инструкции для SMO1000A-S

Бренды по названию

Популярные бренды

Scientific SMO1000A-S, Руководство пользователя

Результаты поиска

Содержание SMO1000A-S

Отзывы:

Похожие инструкции для SMO1000A-S

Бренды по названию

Популярные бренды