Scientific SMO1000A-S Скачать руководство пользователя страница 156

Страница: 156 / 176

User Manual SMO1000A-S

156/176

LED Test

LED test is used to test that if the button lights work well.

Press the

Utility

button on the front panel to enter the UTILITY function menu.

Press the

Next Page

softkey to go to the second page of the UTILITY function menu.

Press the

Next Page

softkey to go to the third page of the UTILITY function menu.

Press the

Do Self Test

softkey to enter the SELFTEST function menu.

Press the

LED Test

softkey to enter the keyboard test interface, as the picture shown

below.

Figure 83 LED Test

According to the prompting information displaying on the screen, press the

Single

button continually to light the button lights one by one. The first time to press the

Single

button, the

Run/Stop

button displays red, and the second press the

Run/Stop

button displays green. Then the other button lights will be lighted one by one. At last all

the lights will be lighted at the same time.

Press the

Run/Stop

button to exit the LED test program.

Содержание SMO1000A-S

















































































































































































Результаты поиска

Содержание SMO1000A-S

Отзывы:

Похожие инструкции для SMO1000A-S

Бренды по названию

Популярные бренды

Scientific SMO1000A-S, Руководство пользователя

Результаты поиска

Содержание SMO1000A-S

Отзывы:

Похожие инструкции для SMO1000A-S

Бренды по названию

Популярные бренды