Rowe BC-1200 Скачать руководство пользователя страница 106 | Manualshive

Страница: 106 / 217

background image

Section 4: Troubleshooting

25238802

4-35

DETCTRS ON LONG

Symptom:

While replenishing, more than one detector was blocked too long.

Corrective Action:

During the last replenish cycle, the system detected a coin pulse from the dispenser that was much longer than normal.
Most likely, an incorrect change load has been deposited into one of the change buckets.

1. A detector LED could have burned out during the replenish cycle. If the LEDs are lit, reset the bill changer

and see if it goes back into

SHUTDOWN.

If so, refer to new status message that will appear.

2. If the bill changer stays in service, then check the photo detectors (per

Section 3

) and wiring.

3. If all three LEDs are not lit, check the

+5 VDC LED

on the power supply. If the

+5 VDC LED

is

OFF,

check

the power supply. If the

+5 VDC LED

is

ON,

check the harness.

4. Also, check the upper coin chute for anything that would hold a coin up and block the detectors.

5. If everything looks OK, replace the CCC.

6. To restore the bill changer to service, press the

FUNCTION

button after correcting the problem.

For a more complete troubleshooting sequence, refer to Troubleshooting Chart 040 at the end of this
DETECTOR troubleshooting.

«
...
104
105
106
107
108
...
»

Содержание BC-1200


























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BC-1200

AC 500 CoinCo BA30BAB

Бренд: American Changer Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды