Rowe BC-1200 Скачать руководство пользователя страница 34

Страница: 34 / 217

Section 2: Installation & Programming

25238802

2 - 9

4. Hold the bag securely while you tip the hopper forward. Tap the hopper against the rap rod and return it to

the upright position. Repeat two or three more times to ensure that the hopper is completely empty.

4. Hoppers may also be removed from the machine and inverted over the bag to empty. When replacing the

hopper, be sure it is sitting securely in the pivot brackets and snug against the back plate.

5. Empty the change from each of the change escrow buckets by pressing a

TEST VEND

switch. When the hopper

motors start, turn the bill changer power OFF then ON. Repeat for each of the three

TEST VEND

switches.

This will completely empty the changer of all coins.

OPERATIONAL INFORMATION

The bill and coin changer uses several visual indicators and controls. The location of these controls and indicators
are as follows:

ON-OFF Switch

Located on the front of the power control center

Circuit Breakers

Located on the front of the power control center (four total)

Dollars Accepted Counter

Located on the front of the power control center

Test Switches

Located on the front of the power control center (three total)

Voltage LED’s

+5 VDC, +12 VDC, +30 VDC, and +40 VDC are located on the front of the power control
center

SERVICE/PROGRAMMING

Located on the computer control board

Switches

Status Display

Located on the computer control board

MONEY RETURN Switch

Located behind the MONEY RETURN lever on the front of the machine (BC-1200)
Located behind the faceplate (BC-1400)

Figure 2-4. Unloading the Hoppers

Содержание BC-1200


























































































































































































































Результаты поиска

Содержание BC-1200

Отзывы:

Похожие инструкции для BC-1200

Бренды по названию

Популярные бренды

Rowe BC-1200, Руководство по обслуживанию на поле и каталог запасных частей

Результаты поиска

Содержание BC-1200

Отзывы:

Похожие инструкции для BC-1200

Бренды по названию

Популярные бренды