Rowe BC-1200 Скачать руководство пользователя страница 102

Страница: 102 / 217

Section 4: Troubleshooting

25238802

4-31

For a more complete troubleshooting sequence, refer to Troubleshooting Chart 030 at the end of this COIN
DETECTOR troubleshooting.

CK COIN DETECTORS

Symptom:

More than one coin detector was blocked while the bill changer was in

STANDBY.

One of the buckets may have

an incorrect change load, or one of the hopper motors may have been running in standby mode.

Corrective Action:

More than one of the coin photodetector inputs is, or was, giving an incorrect signal.

1. One of the LEDs on the dispenser may have burned out. If any LEDs are out, check the wiring to that LED.

Check the LEDs and replace any defective LEDs.

2. If all LEDs are not lit, check the

+5 VDC LED

on the power control center. If it is not lit, check the power supply.

If it is lit, check +5V power distribution lines in the harness (Blue wires).

3. Press the

FUNCTION

button. If the message reappears, check for dirt on the detectors and LEDs. If they are

clean, check the coin photodetectors (per

Section 3

). If they are OK, check the wiring from the photodetectors

to the CCC for open connections or shorts to Ground. If no problems are found, replace the CCC.

4. If this message does not reappear after resetting the bill changer, check the wiring to the hopper motors and

coin detectors. If no problems are found, replace the CCC. To restore the bill changer to operation, press
the

FUNCTION

button after correcting the problem.

For a more complete troubleshooting sequence, refer to Troubleshooting Chart 030 at the end of this COIN
DETECTOR troubleshooting.

NOTE:

This error code may be the result of a leaky output to the left hopper drive motor from the CCC. If this
is the case, replace the CCC.

NOTE:

This error code may be the result of a leaky output to the left hopper drive motor from the CCC. If this
is the case, replace the CCC.

Содержание BC-1200


























































































































































































































Результаты поиска

Содержание BC-1200

Отзывы:

Похожие инструкции для BC-1200

Бренды по названию

Популярные бренды

Rowe BC-1200, Руководство по обслуживанию на поле и каталог запасных частей

Результаты поиска

Содержание BC-1200

Отзывы:

Похожие инструкции для BC-1200

Бренды по названию

Популярные бренды