Rowe BC-1200 Скачать руководство пользователя страница 54

Страница: 54 / 217

Section 3: Routine Service

25238802

3 - 3

REMOVING A JAMMED BILL FROM THE BILL ACCEPTOR (BC-1200 ONLY)

Jammed bills can be easily removed in the following manner:

1. Unlock and open the top door. Turn the power

OFF

2. Slide the bill acceptor out until it stops.

3. Remove the jammed object from the acceptor.

BILL JAMMING CHECK LIST

If bills jam frequently, perform the following checks and corrective procedures

(see Figure 3-2)

1. Make sure that all belts stay centered on all rollers when the transport is running in either the forward or the

reverse direction.

2. Check to see that both timing belts are snug (not too loose or too tight).

3. Make sure that the rubber drive rollers are not loose or worn.

4. Exit flipper must work freely.

5. Be sure that the inlet Nylon idler roller rotates freely and moves up and down freely in its slot. The retaining

springs must also slide without bind in the guide slots and exert adequate force on the idler roller.

6. Bottom track bill surfaces must be free of dirt, moisture, burrs, projections, rough spots, etc., which might drag

or hang up on the surface of bill.

7. The magnetic head must have a bevelled edge on both front and back to keep both bill edges from becoming

caught in forward or reverse.

8. The rubber rollers opposite the magnetic head assembly must rotate freely. No dirt, moisture, burrs,

projections, or rough spots can be on the magnetic heads or magnetic head holder.

Содержание BC-1200


























































































































































































































Результаты поиска

Содержание BC-1200

Отзывы:

Похожие инструкции для BC-1200

Бренды по названию

Популярные бренды

Rowe BC-1200, Руководство по обслуживанию на поле и каталог запасных частей

Результаты поиска

Содержание BC-1200

Отзывы:

Похожие инструкции для BC-1200

Бренды по названию

Популярные бренды