Rowe BC-1200 Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 217

background image

BC-1200-1400 Bill and Coin Changer

3 - 8

25238802

3. Turn the transport over and connect the Common lead of a voltmeter to P701, Pin 10. Connect the other lead

to P701, Pin 9. Turn the transport motor drive shaft very slowly by hand. The meter should alternately read
voltages below 0.7 VDC then above 3.8 VDC.

4. One rotation of the motor drive shaft will produce 100 pulses.

5. If you were using the Anti-Pullback feature, be sure to re-enable it.

Testing BC-1200-1400 Transport Photocells

The transport photocells are automatically checked each time the transport is turned on. Each photocell and light
combination goes through a short test and brightness adjustment process. This process continues as long as the
transport receives power. No adjustments can be made; however, a bad photocell can be detected with a voltmeter.
The following measurements are all made with the Common lead of the voltmeter connected to P701, Pin 10 on the
transport (the voltmeter should have a 10 megohm impedance).

Photocell

VI - Transport Inlet

VF - Flipper Cell

VT - Transmissive Cell

VR - Reflective Cell

Action

No Action - Leave the inlet open

Block the light path by inserting paper
or a bill into the transport opening

No Action - Leave flipper in rest
position

Block the light path with the flipper

No Action - Leave the light path open

Block the light path by inserting paper
or a bill between the transmissive cell
and the transmissive/reflective LED in
the middle of the transport

No Action - Leave the light path open

Insert a white piece of paper be-
tween the transmissive cell and the
transmissive/reflective LED in the
middle of the transport

Voltage Expected

P701, Pin 7 should be between
0.2 VDC and 1.9 VDC

P701, Pin 7 should increase at least
0.5 volts from the reading taken with
the inlet open. The transport motor
should start running forward. Hold the
bill in place until you finish the reading,
then remove the bill and let the
transport finish cycling.

P701, Pin 5 should be less than 1.0
VDC

P701, Pin 5 should be greater than
2.8 VDC

P701, Pin 4 should be 0.74 VDC to
1.25 VDC

P701, Pin 4 should increase by at
least 0.75 VDC from the reading
taken with the light path open

P701, Pin 6 should be between 0.8
VDC and 2.0 VDC

P701, Pin 6 should increase by at
least 0.25 VDC from the reading
taken without white paper inserted.

«
...
57
58
59
60
61
...
»

Содержание BC-1200


























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BC-1200

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды