Rowe BC-1200 Скачать руководство пользователя страница 101

Страница: 101 / 217

BC-1200/1400 Bill and Coin Changer

4-30

25238802

4. If this message does not reappear after resetting the bill changer, check the wiring to the hopper motors and

coin detectors. If no problems are found, replace the CCC. To restore the bill changer to operation, press
the

FUNCTION

button after correcting the problem.

For a more complete troubleshooting sequence, refer to Troubleshooting Chart 030 at the end of this COIN
DETECTOR troubleshooting.

CK R COIN DETCTR

Symptom:

The right coin detector was blocked while the bill changer was in the

STANDBY

state. One of the buckets may have

an incorrect change load.

Corrective Action:

The right coin photodetector input is, or was, giving an incorrect signal / one of the hopper motors may have been
running in standby mode.

1. The center LED on the dispenser may have burned out. If the LED is still

OFF,

check the wiring to that LED.

Check the LED and replace it if it is defective.

2. If all LEDs are not lit, check the

+5 VDC LED

on the power control center. If it is not lit, check the power supply.

If it is lit, check +5V power distribution lines in the harness (Blue wires).

3. Press the

FUNCTION

button. If the message reappears, check for dirt on the right detectors and LED. If they

are clean, check the coin photodetector (per

Section 3

). If they are OK, check the wiring from the

photodetectors to the CCC for an open connection or a short to Ground. If no problems are found, replace
the CCC.

4. If this message does not reappear after resetting the bill changer, check the wiring to the hopper motors and

coin detectors. If no problems are found, replace the CCC. To restore the bill changer to operation, press
the

FUNCTION

button after correcting the problem.

NOTE:

This error code may be the result of a leaky output to the left hopper drive motor from the CCC. If this
is the case, replace the CCC.

Содержание BC-1200


























































































































































































































Результаты поиска

Содержание BC-1200

Отзывы:

Похожие инструкции для BC-1200

Бренды по названию

Популярные бренды

Rowe BC-1200, Руководство по обслуживанию на поле и каталог запасных частей

Результаты поиска

Содержание BC-1200

Отзывы:

Похожие инструкции для BC-1200

Бренды по названию

Популярные бренды