Rowe BC-1200 Скачать руководство пользователя страница 62

Страница: 62 / 217

Section 3: Routine Service

25238802

3-11

Bill Stacker

HOME SWITCH ADJUSTMENT

A stacker cycle will start each time a

TEST

switch is

pressed. Adjust the stacker HOME switch as follows:

1. Turn the power

OFF

and remove the bill stacker

from the bill changer.

2. Hold the motor brake

(disengaged) and manually

rotate the motor shaft until the stacker is in the

HOME

position (the stacker push plate is at its inner

most position).

3. Disconnect the lower link and move it to the side.

4. Adjust the cam switch by loosening the adjustment

screw and rotating the switch until the cam pushes
the spring against the switch body as shown in

Figure 3-7.

5. Tighten the adjustment screw, reconnect the lower

link and install the bill stacker in the bill changer.

6. Turn the power

and check stacker operation.

Figure 3-7. Stacker Switch Adjustment

NOTE:

BC-1400

To remove the stacker from the BC-1400, it is necessary to get into an OFF HOME
condition. To do this, press one of the TEST VEND switches and as the stacker push
plate reaches its maximum travel, turn the power off.

Lower Link

Removed

Adjustment

Screw

Cam

Spring

Содержание BC-1200


























































































































































































































Результаты поиска

Содержание BC-1200

Отзывы:

Похожие инструкции для BC-1200

Бренды по названию

Популярные бренды

Rowe BC-1200, Руководство по обслуживанию на поле и каталог запасных частей

Результаты поиска

Содержание BC-1200

Отзывы:

Похожие инструкции для BC-1200

Бренды по названию

Популярные бренды