RKC INSTRUMENT Z-TIO-G Скачать руководство пользователя страница 204 | Manualshive

Страница: 204 / 246

background image

9. COMMUNICATION DATA DESCRIPTION

IMS01T28-E4

9-96

Power feed forward (PFF) selection

RKC communication
identifier

JK

Modbus
register address

ch1: 0425H (1061)
ch2: 0426H (1062)

Use to select Use/Unuse of the Power feed forward (PFF) function.

Attribute:

R/W

Digits:

7 digits

Number of data:

2 (Data of each channel)

Data range:

0: Unused
1: Used

Factory set value:

0

Related parameters:

PFF power supply frequency (P. 9-95),
Measurement power supply frequency (P. 9-97), PFF input voltage (P. 9-97),
PFF reference voltage (P. 9-98),
Output compensation factor for PFF reference voltage (P. 9-98),

Output compensation captured value for PFF reference voltage (P. 9-99),
PFF gain (P. 9-99)

Function:

The Power feed forward function monitors the electrical load through a dedicated
transformer, and adjusts manipulated output to compensate power supply fluctuation.
If the Power feed forward (PFF) input voltage is decreased to about 70 % or less of
the rated value, the Power feed forward function is turned off. At this time, the
control mode will return to the normal control (the same control as without the
Power feed forward function).

The Power feed forward function is used together with the Output change rate limiter
function, the Manipulated output value may exceed the limit of the Output change rate
limiter.

When the Power feed forward function is set to “1: Used,” the function is turned off under
the following condition.



When no Power feed forward (PFF) input is used (no Power feed forward transformer is connected)



When Power feed forward (PFF) input voltage is decreased to about 70 % or less of the rated value

Always use the dedicated power feed transformer (PFT-02A) included.

PID compute

Output change

rate limiter

Power feed

forward

Actual Manipulated
output value (MV)

Relationship between the Power feed forward and Output change rate limiter

Z-TIO-G

module

SSR

Control output

Controlled

object

Operating unit

Load power supply

Sensor input

Control
output

Power feed forward transformer

(PFF input)

«
...
202
203
204
205
206
...
»

Содержание Z-TIO-G























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Z-TIO-G

TLE Scalable 150

Бренд: GE Страницы: 6

Бренд: GE Страницы: 3

Бренд: GE Страницы: 80

PACSystems* RX3i

Бренд: GE Страницы: 39

PACSystems* RX3i

Бренд: GE Страницы: 35

PACSystems* RX3i

Бренд: GE Страницы: 3

PACSystems* RX3i

Бренд: GE Страницы: 169

PACSystems RX7i

Бренд: GE Страницы: 317

Бренд: KAR-TECH Страницы: 28

Бренд: 2iB Страницы: 5

Go!Control Panel

Бренд: 2gig Technologies Страницы: 78

Бренд: EasyIO Страницы: 12

Бренд: RMG Страницы: 6

Бренд: Acclaim Lighting Страницы: 32

Бренд: Samson Страницы: 73

Бренд: Häfele Страницы: 2

Бренд: Häfele Страницы: 24

Бренд: GBD Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды