RKC INSTRUMENT Z-TIO-G Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 246

background image

5. WIRING

IMS01T28-E4

5-13

5.6 Connections for Loader Communication

Each function module (Z-TIO, Z-DIO and Z-CT) is equipped standard with a Loader communication
connector.
The module Loader communication connector, our COM-K USB communication converter (sold separately)

1

,

and a personal computer can be connected with the appropriate cables, and our communication tool
(PROTEM2)

2

can be installed on the computer, to enable data management monitoring and settings from

the computer.
The only data that can be communicated by Loader communication is data of a module that is connected by
a Loader communication cable. (Data of other joined modules cannot be communicated.)

1

A loader communication cable (optional) is required for the connection to the Loader communication connector on the
module. USB communication converter COM-K-1 (with Loader communication cable [cable length: 1 m])

2

The communication tool (PROTEM2) can be downloaded from the RKC official website:
https://www.rkcinst.com/.

USB communication

converter COM-K

USB cable
(COM-K accessory)

Connected to loader

communication

connector of the

module

Connected to USB

port of a personal

computer

Loader communication
cable (W-BV-01)
[Option]

Connected to loader

communication

connecter

Connected to

USB connecter

Loader

communication

connecter



Communication tool (PROTEM2)
Software operation environment:
PROTEM2: Windows XP (Service Pack 2) or higher

(PROTEM2 needs Microsoft .NET Framework 4.0 or later)



Communication port of host computer

USB port: Based on USB Ver. 2.0



Communication settings on the computer

(Values other than the communication port are fixed.)

Communication speed: 38400 bps
Start bit:

1

Data bit:

8

Parity bit:

Without

Stop bit:

1

Communication port:

0 to 255

The module address for Loader
communication is fixed at “0.”
The setting of the address
setting switch is disregarded.

Personal computer

Do not unplug the USB cable while
the power to the instrument is ON.

The Loader port is only for parameter setup.

The Loader communication corresponds to the RKC communication protocol “Based on ANSI
X3.28-1976 subcategories 2.5 and B1.”

For the COM-K, refer to the

COM-K Instruction Manual (IMR01Z01-E



).

«
...
49
50
51
52
53
...
»

Содержание Z-TIO-G























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Z-TIO-G

Бренд: UE Страницы: 4

Бренд: D+H Страницы: 36

Бренд: D-Box Страницы: 4

Бренд: D+H Страницы: 36

Бренд: Haldex Страницы: 8

Бренд: Magellan Страницы: 2

Бренд: S&P Страницы: 12

Бренд: S&C Страницы: 34

Бренд: S&C Страницы: 32

IntelliCap Plus

Бренд: S&C Страницы: 32

Бренд: S&P Страницы: 12

Бренд: S&C Страницы: 35

Бренд: Balboa Страницы: 74

Бренд: Cadac Страницы: 4

Бренд: YOKOGAWA Страницы: 150

Бренд: YOODA Страницы: 3

Бренд: YMGI Страницы: 8

Бренд: ZKTeco Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды