RKC INSTRUMENT Z-TIO-G Скачать руководство пользователя страница 113

Страница: 113 / 246

9. COMMUNICATION DATA DESCRIPTION

IMS01T28-E4

9-5

Operation mode state monitor

RKC communication
identifier

Modbus
register address

ch1: 0008H (8)
ch2: 0009H (9)

Each operation mode state of the Z-TIO module is expressed in bit data items.

Attribute:

Digits:

digits

Number of data:

2 (Data of each channel)

Data range:

RKC communication:

ASCII code data

The operation mode state is assigned as a digit image in ASCII code data of 7 digits.

ASCII code data of 7 digits:

Most significant digit ············ Least significant digit

Data:

0: OFF 1: ON

Modbus:

0 to 15 (bit data)

The operation mode state is assigned as a bit image in binary numbers.

Bit image: 0000000000000000

Bit 15 ····················· Bit 0

Bit data: 0: OFF 1: ON

Factory set value:



Related parameters:

Auto/Manual transfer (P. 9-15), Remote/Local transfer (P. 9-16),

RUN/STOP transfer (P. 9-16), Operation mode (P. 9-37)

When the

Operation mode (P. 9-37)

is “0: Unused,” all operation mode state monitor data is

“0: OFF.”

Bit 0:

Control STOP

Bit 1:

Control RUN

Bit 2:

Manual mode

Bit 3:

Remote mode

Bit 4 to Bit 15: Unused

Least significant digit: Control STOP
2nd digit:

Control RUN

3rd digit:

Manual mode

4th digit:

Remote mode

5th digit to Most significant digit:

Unused

Содержание Z-TIO-G























































































































































































































































Результаты поиска

Содержание Z-TIO-G

Отзывы:

RKC INSTRUMENT Z-TIO-G, Инструкция по эксплуатации, Страница: 113 / 246

Результаты поиска

Содержание Z-TIO-G

Отзывы: