RKC INSTRUMENT Z-TIO-G Скачать руководство пользователя страница 203

Страница: 203 / 246

9. COMMUNICATION DATA DESCRIPTION

IMS01T28-E4

9-95

9.3.3 Setting parameters exclusive to Z-TIO-G module

Sensor bias

RKC communication
identifier

Modbus
register address

ch1: 0422H (1058)
ch2: 0423H (1059)

This is used to make a bias setting of the RTD input.

Attribute:

R/W

Digits:

7 digits

Number of data:

2 (Data of each channel)

Data range:



3.0000 to



3.0000



Factory set value:

0.0000

Related parameters:

Input type (P. 9-45)

This parameter is active when the instrument has RTD input.

PFF power supply frequency

RKC communication
identifier

Modbus
register address

0424H (1060)

Set power supply frequency of the Power feed forward (PFF) input.

Attribute:

R/W

Digits:

7 digits

Number of data:

1 (Data of each module)

Data range:

0: 50 Hz
1: 60 Hz
2: Automatic setting

Factory set value:

Related parameters:

Power feed forward (PFF) selection (P. 9-96),
Measurement power supply frequency (P. 9-97)

This parameter is activated when the Power feed forward (PFF) input is used.

The SRZ should be used with the default value “2: Automatic setting” in normal operations.

Содержание Z-TIO-G























































































































































































































































Результаты поиска

Содержание Z-TIO-G

Отзывы:

Похожие инструкции для Z-TIO-G

Бренды по названию

Популярные бренды

RKC INSTRUMENT Z-TIO-G, Инструкция по эксплуатации

Результаты поиска

Содержание Z-TIO-G

Отзывы:

Похожие инструкции для Z-TIO-G

Бренды по названию

Популярные бренды