RITE-HITE FasTrax XL, Инструкция по установке/обслуживанию/эксплуатации

Страница: 62 / 92

FasTrax
®
XL
Installation/Service/Owner's Manual
Rite‑Hite
®
62 Publication: AMEN00316 2020-07-06
MAINTENANCE
Planned Maintenance
CUSTOMER: JOB # SERIAL # DATE:
TASK
RECOMMENDED P.M. IN MONTHS
INSPECT AND PERFORM THE FOLLOWING:
1 6 12 18 24 30 36
Verify Operation
      
See "Verify Operation" on page 61
Auto Re-Feed
–
 
–

–

Verify auto re-feed is operational
Brake

–

–

–

Verify that brake stops the door at open and closed positions as well as when
stopped in the middle of travel To move the curtain manually, turn the brake
release handle to the disengaged position The curtain should be able to be
moved manually If brake is making noise, adjust
Controls/Wiring
– –

–

–

Clean and check all connections with disconnect off. All wires are free from
moving parts
Counterweight Belt
–
 
–

–

Replace if visibly torn, damaged or frayed
Curtain
–

–
 
–

Inspect for wear or damage; patch immediately to prevent condensation or
frost buildup Clean with warm soapy water Check drive spheres; if missing or
damaged, replace
Door Assembly
– –

–

–

Perform visual inspection for damage Tighten all hardware Replace any worn
labels Use air hose to remove dust and debris
Door Operation
– –
    
Operate door and make sure all operations are functioning properly
Drive Tube
– –

–

–

Drive tube gear is centered over track groove Bearing set screws and mounting
bolts are tight
Gearbox
– –

–

–

Gearbox fluid level; fill with Mobil ‑ SHC 624 or Phillips 66 ‑ Syncon 32 if low. Lock
collar set screws Torque arm bolts are tight
Encoder/Chain/
Sprockets
– –

–

–

Verify encoder chain and sprocket set screws are tight Verify lock collar on
encoder is tight Check open and close positions; adjust as required
Lintel Seal
– –

–

–

Verify lintel seal is sealing wall properly
Motor
– –

–

–

Motor/gearbox bolts, torque to 71in-lbs [8Nm] Junction box to verify connections
are tight
Non-Powered Opening
(Optional) – –

–

–

With power on, operate hand lever to verify chain hoist puts door into fault and
opens door Lubricate chain, sprockets, check set screws and alignment Check
spring and cable clamps
Photoeyes
–
     
Both photoeyes reverse the curtain. LEDs on receiver should go on/off. Clean
emitter and receiver lens Test curtain position photoeyes
Lower Tracks
–
     
Perform visual inspection Verify proper width and tighten all hardware
Lubrication* of tracks may be
required more than every 6 months,
based on usage and environmental
conditions
Perform visual inspection Verify proper width and tighten all hardware Lubrication
of tracks is the sole responsibility of the end user If door is mounted in a dirty
environment, it may be required to remove the existing grease prior to adding new
Verify foam seal is present
Track Retention Strips
– –

–

–

Replace if cracked
Virtual Vision
(Optional)
– –
    
Red LEDs are lit with movement on opposite side
Vision
(Optional)
–
 
–
 
–
Verify that all visions are in place Replace if torn or cloudy
Clean with warm soapy water
Windbar
(Optional)
–
     
Verify windbar straps are rolling up correctly and not damaged
Verify windbar clamps and attachment plates are securely fastened
* Use High-Temperature Synthetic Grease with PTFE
(Polytetrafluoroethylene).
• The synthetic oil base in this food-grade silica-thickened grease
increases the time before the next application
• Contains a PTFE additive that reduces friction and waterproofs metal
surfaces, preventing rust and corrosion
• NSF rated H1 for applications with incidental food contact
• Temperature range is -45° to +450°F [-45° to +232°C]
• Color is white
• McMaster Carr # 1378K33 - 141oz cartridge