Ricoh VT3500 Скачать руководство пользователя страница 84 | Manualshive

Страница: 84 / 330

background image

4.8 SECOND FEED ROLLER MECHANISM

[Drive Mechanism]

The lower second feed roller [I] is driven by the sector gear [C] and the feed
roller gear [E]. When the paper feed solenoid [G] turns on, the link [F]
combined with the paper feed roller sector stopper [H] are pulled.

The bearing [J] of the sector gear moves along the second feed roller cam
face. When the bearing of the sector gear comes to the top of the lower
second feed roller cam [A], the stopper [B] is released from the sector gear
as a clearance is formed between the pin of the sector gear [D] and the
stopper.

When the feed roller gear turns counterclockwise, its rotation is not
transmitted to the lower second feed roller due to the one-way clutch bearing
press-fit into the gear.

When the bearing of the sector gear moves up from the bottom of the second
feed roller cam, the sector gear turns counterclockwise and the feed roller
gear turns clockwise. As the rotation of the feed roller gear is transmitted to
the lower second feed roller, the lower second feed roller turns clockwise to
feed the paper to the drum section.

[D]

[H]

[G]

[B]

[A]

[F]

[E]

[C]

[I]

[J]

1 December 1993

2-48

«
...
82
83
84
85
86
...
»

Содержание VT3500











































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VT3500

Бренд: Samsung Страницы: 82

Бренд: Samsung Страницы: 2

Бренд: Lanier Страницы: 3

Бренд: OKIDATA Страницы: 13

imageRUNNER ADVANCE DX C478iZ

Бренд: Canon Страницы: 208

imageRUNNER ADVANCE DX C477iFZ

Бренд: Canon Страницы: 92

Бренд: Citizen Страницы: 80

Бренд: Oce Страницы: 306

Бренд: Printek Страницы: 31

Бренд: Xerox Страницы: 128

Бренд: Riso Страницы: 208

Бренд: Oki Страницы: 20

Бренд: Oki Страницы: 336

8200DX - Phaser Color Solid Ink Printer

Бренд: Xerox Страницы: 2

Бренд: SEWOO Страницы: 12

Бренд: MIMAKI Страницы: 28

Бренд: Star Страницы: 2

Бренд: Xante Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды