Ricoh VT3500 Скачать руководство пользователя страница 32

Страница: 32 / 330

Index No.

Name

Function

Master Eject
Clamper Solenoid

Opens the master clamper to eject the
master.

Master Feed
Clamper Solenoid

Opens the master clamper to clamp the
master.

Master Eject Solenoid Presses the lower master eject roller

against the drum surface.

Sensors

Original Registration
Sensor

Informs the CPU when the original
activates the sensor. Also, detects the
original misfeed.

2nd Original Sensor

Informs the CPU when the original
activates the sensor. Also, detects
original misfeeds.

1st Original Sensor

Informs the CPU if the original is set in
the ADF mode.

Original Width Sensor Informs the CPU of the original width.

Paper End Sensor

Informs the CPU if the paper is set on
the paper table.

Paper Width Sensor

Informs the CPU of the paper width.

Paper Table Height
Sensor

Informs the CPU if the paper table is at
the paper feed position.

Paper Table Lower
Limit Sensor

Informs the CPU if the paper table is at
the lowest position.

Printing Pressure
Sensor

Informs the CPU if printing pressure is
applied. Also, detects paper misfeeds.

1st Paper Exit Sensor Detects paper misfeeds.

2nd Paper Exit
Sensor

Detects paper misfeeds.

2nd Drum Position
Sensor

Checks the position of the drum.

Drum Rotation
Sensor

Supplies timing pulses to the CPU
based on the main motor speed.

Image Position
Sensor

Informs the CPU of the image position.

1st Drum Position
Sensor

Checks the position of the drum.

1 December 1993

1-18

Содержание VT3500











































































































































































































































































































































Результаты поиска

Содержание VT3500

Отзывы:

Похожие инструкции для VT3500

Бренды по названию

Популярные бренды

Ricoh VT3500, Руководство по обслуживанию

Результаты поиска

Содержание VT3500

Отзывы:

Похожие инструкции для VT3500

Бренды по названию

Популярные бренды