Ricoh VT3500 Скачать руководство пользователя страница 217

Страница: 217 / 330

2. SERVICE PROGRAM MODE

2.1 SERVICE PROGRAM MODE OPERATION

The service program (SP) mode is used to check electrical data and change
modes or change adjustment values.

2.1.1 Service Program Mode Access Procedure (for engineers)

All service program modes can be accessed with this procedure.
1. Press the keys on the operation panel in the following order:

a) Clear Modes key
b) Clear key
c) Combine 2 Originals key
d) Enter key

2. The following menu is displayed on the LCD when the SP mode is

accessed.

SP–MODE
PROGRAM No.

3. Using the number keys, enter the desired SP mode number (listed in the

service program table.)

NOTE: SP mode number can be shifted up or down by pressing the Zoom

key ("+" or "–").

4. To cancel the SP mode, press the Clear Modes key.

2.1.2 Service Program Mode Access Procedure (for users)

This procedure allows users to access only the service program modes that
are marked with an asterisk in the service program table.

1. Press the keys on the operation panel in the following order:

a) Clear Modes key
b) Clear key
c) Enter key

2. The following menu is displayed on the LCD when the SP mode is

accessed.

SP–MODE
PROGRAM No.

3. Using the number keys, enter the desired SP mode number (listed in the

service program table.)

4. To cancel the SP mode, press Clear Modes key.

1 December 1993

4-11

Содержание VT3500











































































































































































































































































































































Результаты поиска

Содержание VT3500

Отзывы:

Похожие инструкции для VT3500

Бренды по названию

Популярные бренды

Ricoh VT3500, Руководство по обслуживанию

Результаты поиска

Содержание VT3500

Отзывы:

Похожие инструкции для VT3500

Бренды по названию

Популярные бренды