Ricoh VT3500 Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 330

background image

1. 0

≤

L

≤

7 mm (L=0, 1, 2, ..., 7)

The image of the original is moved backwards by advancing the master feed
timing during the master making process. First, the print must have a 10
millimeters blank margin at its leading edge. This is to let the machine easily
peal the print off the drum. To allow for the margin, a 10 millimeters margin
must also be made on the master; so plotting on the master starts from the
line (on the master) that corresponds to the first line on the print immediately
following the 10 millimeters margin. Prints and master will always have this
margin when the value of L is between 0 and 7 millimeter

If the shifting length L is +7 millimeters, the master starts being fed and the
master plotting signal is energized when the original is fed 8.5 millimeters
(after the drum stops rotating). The image is scanned from 3 millimeters after
the leading edge of the original. Then the scanned image is plotted on the
master from the line (on the master) that corresponds to 10 millimeters from
the leading edge of the print.

The master plotting signal is de-energized when the original scanning for the
plotting area is finished. Then, the master feed motor turns off.

410 mm(Max.)

15.5 mm

218.5 in Drum Rotation

High Speed

8.5 mm

20.5 mm

Second Drum Position

Sensor

[Master Making Process]

Main Motor Reversing

Original Registration

Sensor

Original Transport

Motor

Master Feed Motor

Original Scanning

Signal

Master Plotting Signal

15.5 mm

3 mm

15 mm

8.5 mm

Scanning Signal

Start Position

Exposure Glass

CCD Scan Line

Original Registration

Sensor

Original

Guide Plate

Plotting Signal

Start Position

1 December 1993

2-25

«
...
59
60
61
62
63
...
»

Содержание VT3500











































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VT3500

Бренд: Oki Страницы: 6

Бренд: Oki Страницы: 44

Бренд: Oki Страницы: 13

Бренд: Oki Страницы: 20

Бренд: Oki Страницы: 2

Бренд: Oki Страницы: 28

870 - SuperScript B/W Laser Printer

Бренд: NEC Страницы: 52

SuperScript 1800

Бренд: NEC Страницы: 8

Бренд: Oki Страницы: 268

Бренд: Oki Страницы: 54

Бренд: Oki Страницы: 54

Бренд: Oki Страницы: 202

Бренд: Oki Страницы: 201

Бренд: Oki Страницы: 103

Бренд: Oki Страницы: 256

Бренд: Oki Страницы: 2

Бренд: Oki Страницы: 36

Бренд: Oki Страницы: 63

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды