Ricoh VT3500 Скачать руководство пользователя страница 59

Страница: 59 / 330

[Electrical Timing for SADF Mode]

T1: The original transport motor starts rotating 1 second after the leading

edge of the original activates the second original sensor.
The ADF drive motor and original pressure solenoid do not work in the
SADF mode.

T2: The original transport motor stops rotating when the original registration

sensor is activated and the original is fed 6.5 millimeters.

T3: When the Master making key is pressed, the original is fed 8.5

millimeters before it stops. From this point on, the timing continues in the
same manner as in the ADF mode.

Master Eject

1 sec

6.5 mm

8.5 mm

First Original Sensor

Master Making Key

Lamp On Signal

ADF Drive Motor

Original Pressure Solenoid

Second Original Sensor

Original Transport Motor

Original Registration

Sensor

Process

Scanning Signal

Start Position

Exposure Glass

CCD Scan Line

Original Registration

Sensor

Original

Guide Plate

6.5 mm

14 mm

8.5 mm

2 mm

1 December 1993

2-23

Содержание VT3500











































































































































































































































































































































Результаты поиска

Содержание VT3500

Отзывы:

Похожие инструкции для VT3500

Бренды по названию

Популярные бренды

Ricoh VT3500, Руководство по обслуживанию

Результаты поиска

Содержание VT3500

Отзывы:

Похожие инструкции для VT3500

Бренды по названию

Популярные бренды