Ricoh VT3500 Скачать руководство пользователя страница 328

Страница: 328 / 330

2. Paper leading edge jams under the second feed roller.

Does the upper second feed roller contact the lower second feed roller
and are both rollers turning normally?

Is the second feed sector gear turning normally?

Is the one-way clutch on the lower second feed roller shaft slip-
ping? (Paper jams frequently at high printing speeds.)

Is the paper detecting pin moving normally?

Is any paper stuck between the guide plates?

Are the guide plates at the correct height?

Check the clearance between the second feed sector
gear stopper and the stopper pin.

Yes

Lightly sand the roller shaft surface with fine
sandpaper (increases the coefficient of friction)
and replace the clutch.

Yes

Adjust the position of the paper detecting pin.

Yes

Adjust the height of the plates.

Remove the paper.

1 December 1993

6-11

Содержание VT3500











































































































































































































































































































































Результаты поиска

Содержание VT3500

Отзывы:

Похожие инструкции для VT3500

Бренды по названию

Популярные бренды

Ricoh VT3500, Руководство по обслуживанию

Результаты поиска

Содержание VT3500

Отзывы:

Похожие инструкции для VT3500

Бренды по названию

Популярные бренды