Ricoh VT3500 Скачать руководство пользователя страница 231

Страница: 231 / 330

2.5.4 Output Check Table

Code

LCD Display

Description

SOL: ADF Original
Pressure Out-

Turns on the ADF original pressure solenoid.

MOTOR: ADF Drive

Out- 2

Turns on the ADF drive motor.

MOTOR: Master Eject

Out- 3

Turns on the master eject motor.

MOTOR: Pressure
Plate Up/Down Out- 4

Turns on the pressure plate up/down motor.

MC: Master Reverse
Roller

Out- 5

Turns on the master reverse roller magnetic clutch.

MOTOR: Vacuum

Out- 6

Turns on the vacuum fan motor.

MOTOR: Air Knife

Out- 7

Turns on the air knife motor.

SIG: Key Counter

Out- 8

Increments key counter.

COUNTER: Master

Out- 9

Not used.

10.

COUNTER: Paper

Out-10

Increments total counter.

11.

SOL: Paper Separation
Release Out-11

Turns on the separation plate release solenoid.

12.

SOL: Ink Supply

Out-12

Turns on the ink supply solenoid.

13.

SOL: Drum Lock

Out-13

Turns on the drum lock solenoid.

14.

SOL: Paper Feed/Print
Pressure Out-14

Turns on the paper feed solenoid and the printing
pressure solenoid.

15.

SOL: Master Feed
Clamper Out-15

Turns on the master feed clamper solenoid.

16.

SOL: Master Eject
Clamper Out-16

Turns on the master eject clamper solenoid.

17.

SOL: Master Eject

Out-17

Turns on the master eject solenoid.

18.

RELAY: Paper Table
Down Out-18

Turns on the paper table drive motor (down).

19.

RELAY: Paper Table
Up

Out-19

Turns on the paper table drive motor (up).

20.

RELAY: Main Motor

Out-20

Turns the drum in the direction opposite to the printing
direction.

21.

SIG: Fluorescent Lamp

Out-21

Turns on the fluorescent lamp.

1 December 1993

4-25

Содержание VT3500











































































































































































































































































































































Результаты поиска

Содержание VT3500

Отзывы:

Похожие инструкции для VT3500

Бренды по названию

Популярные бренды

Ricoh VT3500, Руководство по обслуживанию

Результаты поиска

Содержание VT3500

Отзывы:

Похожие инструкции для VT3500

Бренды по названию

Популярные бренды