Ricoh VT3500 Скачать руководство пользователя страница 212

Страница: 212 / 330

1.2 TABLE OF SERVICE CALL INDICATIONS

Indication

Trouble

Possible Causes

E-01

Neither the right nor the left
cutter switch turns off within 3
seconds of the cutter motor
starting.

1) Drive wire cut

2) Drive section

malfunction

3) Defective cutter switch

E-02

Malfunction in the paper table
drive section.
The lower limit sensor or paper
table height sensor does not turn
on within 7 seconds.

1) Drive worm gear

broken

2) Mounting screw of the

worm gear broken

3) No power supply

E-04

Temperature of the thermal head
is greater than 54°C when the
Master Making key is pressed.

1) Excessive thermal

head temperature

2) Thermistor short

E-05

Malfunction in the image shifting
section.

1) Image position sensor

connector
disconnected

2) Defective image

position sensor

E-06

The drum rotation sensor detects
an incorrect motor speed.

1) Drum lock

2) No power supply

E-07

Malfunction in the program.
When the main SW is turned on,
"E-07" lights up if the ROM is
defective.

Defective ROM

E-08

Temperature of the power supply
unit is greater than 85°C when
the Master Making key is
pressed.

Excessive power supply
unit temperature

E-09

The signal level between
CN109-A8 and GND is over 4.9
volts.

1) Thermistor open.

2) Related connectors

are not connected.
(Main PCB CN109-A8,
image processing
PCB CN404-b8/
CN403-22, or thermal
head drive PCB
CN705-22/ CN703-10.)

1 December 1993

4-6

Содержание VT3500











































































































































































































































































































































Результаты поиска

Содержание VT3500

Отзывы:

Похожие инструкции для VT3500

Бренды по названию

Популярные бренды

Ricoh VT3500, Руководство по обслуживанию

Результаты поиска

Содержание VT3500

Отзывы:

Похожие инструкции для VT3500

Бренды по названию

Популярные бренды