Ricoh VT3500 Скачать руководство пользователя страница 178

Страница: 178 / 330

10.2 MONITOR INDICATION

10.2.1 Cover Open Indicator

Condition

Guidance Display Message

The drum has not been inserted all
the way into the machine.

SET THE DRUM COMPLETELY

Front door is open, master eject unit is
open, or original table (scanner unit) is
open.

CLOSE THE COVER

Paper table is closed, or paper
delivery table is closed.

OPEN THE PAPER
FEED/DELIVERY TABLE

ADF cover is open.

CLOSE THE ADF COVER

NOTE:

1. The above guidance messages are not displayed in the following modes:

•

Make-up mode

•

User program mode

•

Image shifting mode

•

Directional magnification mode

2. The cover open indicator turns off when a cover is closed, or the paper

table and paper delivery table are opened.

10.2.2 Key Counter Indicator:

Condition

Guidance Display Message

Key counter is not set (SP mode data
of address 3 is 1)

SET THE KEY COUNTER

NOTE:

1. If the key counter is taken out during master making, the key counter

indicator does not turn on until master making is completed.

2. If the key counter is taken out while prints are being made, paper feeding

stops, the above message is displayed, and the key counter indicator
turns on.

3. The above message is not displayed in the following cases:

•

The machine is in make-up mode, user program mode, image shifting
mode, or directional magnification mode.

•

Cover open indicator is on.

•

Machine is in operation.

4. Key counter indicator turns off when the key counter is inserted.

1 December 1993

2-142

Содержание VT3500











































































































































































































































































































































Результаты поиска

Содержание VT3500

Отзывы:

Похожие инструкции для VT3500

Бренды по названию

Популярные бренды

Ricoh VT3500, Руководство по обслуживанию

Результаты поиска

Содержание VT3500

Отзывы:

Похожие инструкции для VT3500

Бренды по названию

Популярные бренды