Ricoh VT3500 Скачать руководство пользователя страница 94

Страница: 94 / 330

4.13 CIRCUIT

Component Name

In/Out

Main PCB

Description

CN No.

Signal Level

Paper Table Lower
Limit Sensor [A]

101-15

Signal goes High when the sensor is
interrupted.

Paper Table Height
Sensor [B]

102-18

Signal goes High when the sensor is
interrupted.

Paper Table Down
Button [C]

102-14

Signal goes Low when the button is
pressed.

Paper Table &
Delivery Table
Open Switches [D]

102-7

Pulse signal goes Low when the
paper table and delivery table are
open and the switches are turned on.

Paper End
Sensor [E]

102-6

Pulse signal goes Low when the
sensor detects paper.

Separation Plate
Release Solenoid [F]

Out

104-6

The solenoid is energized when the
signal goes Low.

Paper Feed
Solenoid [G]

Out

103-8

The solenoid is energized when the
signal goes Low.

Paper Table Up
Relay [H]

Out

105-11

The paper table up relay is
energized when the signal goes
Low. (The table moves up.)

Paper Table Down
Relay [I]

Out

105-12

The paper table down relay is
energized when the signal goes
Low. (The table moves down.)

Paper Table Brake
Relay [J]

Out

105-13

Activated for 50 milliseconds when
the paper table reaches the upper or
lower limit. Brake force is applied to
the paper table drive motor.

Common Relay Line
[K]

Out

105-14

Activated when the main switch is
turned on.

GND

CN102-14

-15

CN903

-9

-8

CN903

-6

-7

-4

-5

CN901

-1

CN903

-1

-3

CN502-12

CN503-16

GND

12V

AC-N

CN501-4

AC-N

CN102

-7

CN102-6

CN102-16

-18

-17

CN901-2

GND

CN101-13

-15

-14

FU101

24V

CN104-6

CN104-7

CN103-8

CN103-23

CN104-8
-9

-10
-11
-12
-13

SOL

-12

-13

-14

SSR302

SSR303

-4

-3

-2

3
4

CN303-2

AC-N

SSR301

CN105
-11

CN302-5

12V

[A]

[B]

[C]

[D]

[E]

[F]

[G]

[H]

[I]

[J]

[K]

Paper Return Motor

Table

AC Drive PCB

Paper Detection PCB

PSU

Main PCB

Paper Table

Delivery Table

Drive
Motor

Paper

5 msec

7.5V

24V

7.5V

5 msec

24V

50 msec

1 December 1993

2-58

Содержание VT3500











































































































































































































































































































































Результаты поиска

Содержание VT3500

Отзывы:

Похожие инструкции для VT3500

Бренды по названию

Популярные бренды

Ricoh VT3500, Руководство по обслуживанию

Результаты поиска

Содержание VT3500

Отзывы:

Похожие инструкции для VT3500

Бренды по названию

Популярные бренды