Ricoh VT3500 Скачать руководство пользователя страница 179

Страница: 179 / 330

10.2.3 Master Eject Box Indicator

Condition

Guidance Display Message

The master eject box is not set.

SET THE MASTER EJECT BOX

The master eject box is full. (When
the pressure plate is lowered, the full
master detection sensor does not turn
on.)

EMPTY MASTER
EJECT BOX

NOTE:

1. The Master Eject Box indicator does not turn on during machine

operation.

2. When this indicator turns on, masters cannot be made, but prints can be

made.

3. The above message is not displayed in the following cases:

•

The machine is in make-up mode, user program mode, image shifting
mode, or directional magnification mode.

•

Cover open indicator is on.

•

Machine is in operation.

4. The master eject box indicator turns off when the master eject box is set

or the Reset key is pressed after the master eject box is removed.

10.2.4 Ink Supply Indicator

Condition

Guidance Display Message

During the printing process, the ink
detecting pin does not detect ink on
the ink roller for 20 drum rotations.

LOAD
NEW INK CARTRIDGE

NOTE:

1. In the following cases the above message is not displayed:

•

Cover open indicator ON

•

Key counter indicator ON

•

Master box indicator ON

•

Machine is in operation

2. When the Reset key is pressed after the ink supply indicator turns on, the

drum rotates 40 times. When ink is detected during drum rotation, the
drum stops rotating and the ink supply indicator turns off.

1 December 1993

2-143

Содержание VT3500











































































































































































































































































































































Результаты поиска

Содержание VT3500

Отзывы:

Похожие инструкции для VT3500

Бренды по названию

Популярные бренды

Ricoh VT3500, Руководство по обслуживанию

Результаты поиска

Содержание VT3500

Отзывы:

Похожие инструкции для VT3500

Бренды по названию

Популярные бренды