Ricoh VT3500 Скачать руководство пользователя страница 222

Страница: 222 / 330

No.

Display

Function

Data

Factory

Setting

Comments

71.

Paper Feed
Jam (B)

Displays the total
number of paper feed
jams.

72.

Paper Wrap
Jam (E)/(B)/(E)

Displays the total
number of times that
paper has wrapped
around the drum.

73.

Paper
Delivery Jam
(G)

Displays the total
number of paper
delivery jams.

74.

Master Feed
Jam (C)

Displays the total
number of master
feed jams.

75.

Master
Delivery Jam
(F)

Displays the total
number of master
delivery jams.

76.

Clear Jam
Counter

Clears all jam
counters.

0: No
1: Yes

81.

Proof Print No. Specifies how many

trial prints are made
after making the
master.

0 to 2 sheets

*82.

Skip Feed No.

Selects the feed
interval.

1 to 5

1: Normal
operation
2: One sheet fed
every two drum
rotations
5: One sheet fed
every five drum
rotations

*83.

Auto Reset
Time

Specifies the auto
reset time.

0: No
1: 3 min.
2: 5 min.

90.

Thermal Head
Test

Selects the
background pattern
for the copy made in
the thermal head test;
performs the test.

1 to 40
51 to 90
101 to 140
150 to 190

See Thermal
Head Test section.

91.

Command
Sheet Check

Prints the command
sheet image
(designated area)
together with the
original image.

0: No
1: Yes

See Command
Sheet Check
section.

100. Combine 2

Originals

Displays the total
number of masters
made in combine 2
original mode.

1 December 1993

4-16

Содержание VT3500











































































































































































































































































































































Результаты поиска

Содержание VT3500

Отзывы:

Похожие инструкции для VT3500

Бренды по названию

Популярные бренды

Ricoh VT3500, Руководство по обслуживанию

Результаты поиска

Содержание VT3500

Отзывы:

Похожие инструкции для VT3500

Бренды по названию

Популярные бренды