Ricoh VT3500 Скачать руководство пользователя страница 291

Страница: 291 / 330

8.2 ADJUSTING THE DRUM MASTER DETECTION SENSOR

Purpose: To ensure that the drum master detection sensor correctly detects

the master on the drum.

Adjustment Standard: 0.9 to 1.0 V when the sensor is activated, and 2.0 V

or higher when it is not activated.

1. Slide out the drum unit and remove the master [A] from the drum.

2. Reinstall the drum unit. Press and hold down the Drum Rotation button

until the drum reaches the home position.

3. Remove the right front cover. Then, confirm that the voltage between

TP102 [E] and TP107 [B] on the main PCB is between 0.9 and 1.0 V.

4. If the voltage is outside the specified range, adjust VR102 [C] on the main

PCB.

5. Make a master with a plain original.

NOTE: Make sure the master leading edge is clamped to the drum

clamper and that the master [A] is wrapped correctly on the drum.

6. Make sure that the voltage between TP102 [E] and TP107 [B] on the

main PCB is 2.0 V or higher. At this time, LED102 will light.

[B]

[C]

[D]

[E]

[A]

1 December 1993

5-57

Содержание VT3500











































































































































































































































































































































Результаты поиска

Содержание VT3500

Отзывы:

Похожие инструкции для VT3500

Бренды по названию

Популярные бренды

Ricoh VT3500, Руководство по обслуживанию

Результаты поиска

Содержание VT3500

Отзывы:

Похожие инструкции для VT3500

Бренды по названию

Популярные бренды