Ricoh PCU10 Скачать руководство пользователя страница 91

Страница: 91 / 195

Cleaning method

Any toner remaining on the OPC receives a positive

charge from the pre-cleaning corona. The toner is

attracted to the cleaning carrier which has a negative

charge. Furthermore, negative cleaning bias is applied

to the cleaning roller, and the remaining toner is

attracted to the carrier on the cleaning roller.

Toner collecting mechanism

An 8-pole magnet is provided in the cleaning roller to

attract the cleaning carrier to the surface of the cleaning

roller. The cleaning carrier attracted to the cleaning roller

is cut to a specified height by the doctor blade. Then the

cleaning carrier contacts the photoconductor as the

cleaning roller rotates in a direction reverse to the

photoconductor.
The positively charged toner is attracted by the cleaning

roller through the cleaning carrier. Then, the toner on the

cleaning roller is collected by the scavenging roller

because the roller is supplied with higher bias voltage

than that of the cleaning roller.
The scavenging blade cleans toner from the surface of

the scavenging roller. The toner scraped from the roller

drops to the collecting coil, and rotation of the coil feeds

the toner to the rear.

The toner is sent to the collecting tube through the used

toner outlet pipe. A coil is also provided in the collecting

tube and is rotated by the main motor via the friction

roller, etc. Next, the toner is sent to the toner cartridge.

Cleaning roller

Cleaning bias

Photoconductive

layer

Cleaning

carrier

Toner

Conductive layer

Cleaning bias

(--20

Cleaning roller

Scavenging roller

Scavenging bias

(--10

Bronze seal

Scavenging roller

Toner collecting coil

Scavenging blade

Friction roller

Used toner

outlet pipe

Toner cartridge

Cleaning coil sensor

Sensor disk

Collecting tube

Friction drive disk

1 July 1994

Cleaning

2-55

Содержание PCU10




































































































































































































Результаты поиска

Содержание PCU10

Отзывы:

Похожие инструкции для PCU10

Бренды по названию

Популярные бренды

Ricoh PCU10, Руководство по обучению обслуживанию

Результаты поиска

Содержание PCU10

Отзывы:

Похожие инструкции для PCU10

Бренды по названию

Популярные бренды