Ricoh PCU10 Скачать руководство пользователя страница 97

Страница: 97 / 195

2.8.2 OPC cleaning brush mechanism

When filming material sticks to the surface of the

photoconductor, the surface potential is not easily

attenuated by exposure to light, and dirty background

copies will be made. To prevent this, the OPC is

cleaned at power on after 10,000 copies or more are

made.
The fibers (fine wire) of the cleaning brush beat against

the flicker blade. This causes contaminants to drop from

the brush, so that its cleaning action is not interfered

with. During OPC cleaning, the message

"OPC belt is

being cleaned. Please wait"

is displayed.

The OPC brush is made of bundles of fine, stainless

steel wires. The bundles are looped to improve cleaning

force.
The brush roller is moved from side to side by the

oscillating motor during operation. This is to prevent

flaws in the brush and uneven scraping on the OPC.

2.8.3 Pressure mechanism

The OPC cleaning brush is designed to contact the

surface of the photoconductor only when it is operating.

If it is always in contact with the OPC, a latent image

would be broken by the brush.
In the OPC cleaning mode, the OPC cleaning brush

pressure solenoid is turned ON 2 seconds after the OPC

motor is turned ON and the cleaning brush is pressed

against the OPC. One second later, the OPC cleaning

brush drive solenoid is turned ON, and the gear unit

lowers so the gears can engage.
Next, the OPC cleaning brush motor comes ON for 0.05

seconds to engage the gears. After 1 second, the OPC

cleaning brush motor and the oscillating motor come ON.

OPC drive roller

Backup roller

Film on OPC

Front positioning pin

Flicker

Oscillating motor

Oscillating cam

Cleaning brush

Oscillating pin

OPC cleaning brush

drive solenoid

Pressure

spring

OPC cleaning brush

pressure solenoid

Arm

Cleaning brush

Gear unit

1 July 1994

OPC Filming Removal

2-61

Содержание PCU10




































































































































































































Результаты поиска

Содержание PCU10

Отзывы:

Похожие инструкции для PCU10

Бренды по названию

Популярные бренды

Ricoh PCU10, Руководство по обучению обслуживанию

Результаты поиска

Содержание PCU10

Отзывы:

Похожие инструкции для PCU10

Бренды по названию

Популярные бренды