Ricoh PCU10 Скачать руководство пользователя страница 166

Страница: 166 / 195

2.15.2 Main control board

NOTE

Never adjust VR101. The setting is paint locked at 4

0.05V

between TP115 and TP116.

DIP switch table

Dipswitch No.

Function at ON

Function at OFF

Default Setting

DPS101-1

Allows the use of the service tool access

code which is entered with service tool

[1-02].

Disables the service tool access code which

is entered with service tool [1-02].

OFF

DPS101-2

1) Allows the use of the initial service tool

access code: 99900.

2) Allows the operation of the copier without

entering any user codes, even in the normal

and security accounting modes.

1) Disables the initial service tool access

code: 99900.

2) Allows the selection of the normal and

security accounting modes with service tool

[2-08].

OFF

DPS101-3

Not used.

OFF

DPS102-1

Overseas version (destination identification). Japanese version.

DPS102-2

Not used.

OFF

DPS102-3

Not used.

OFF

DPS103-1

Production use only. (Must be ON.)

DPS103-2

Production use only. (Must be OFF)

OFF

DPS103-3

Not used.

OFF

Electrical Control

1 July 1994

2-130

Содержание PCU10




































































































































































































Результаты поиска

Содержание PCU10

Отзывы:

Похожие инструкции для PCU10

Бренды по названию

Популярные бренды

Ricoh PCU10, Руководство по обучению обслуживанию

Результаты поиска

Содержание PCU10

Отзывы:

Похожие инструкции для PCU10

Бренды по названию

Популярные бренды