Ricoh PCU10 Скачать руководство пользователя страница 176

Страница: 176 / 195

2.16.6 Horizontal transport unit

The horizontal transport unit transports the paper fed

from the LCT to the vertical transport unit of the main

body. It is mounted on the lower portion of the

duplex/exit unit of the main body.

The horizontal transport drive unit is driven by the main

motor through the duplex/exit unit.

The upper horizontal transport guide can be released to

facilitate removal of jammed paper. If the lock lever is

pushed in the direction of the arrow, the lock is released.
Horizontal transport entrance and exit sensors detect

jams in the horizontal transport unit.

2.16.7 Upper transport mechanism

The upper transport unit on the upper part of the LCT

transports paper to the sorter side. The upper transport

roller is driven by the transport drive belt from the

transport motor.

The transport sensor detects jams in the upper transport

unit.

2.16.8 Other mechanisms

Tray lock/release

When the bottom plate of the tray lowers, the arm of the

lock lever is pressed by the bracket of the paper end

sensor, and the lock lever tip is raised to release the

lock. When the bottom plate of the tray is raised, the

lock lever tip is lowered and catches on the tray

positioning bracket so the tray cannot be taken out.

Horizontal transport

exit sensor

Horizontal transport

entrance sensor

Upper horizontal

transport guide

Lock lever

Horizontal transport

roller

Gear (Z25)

Horizontal transport

drive gear

Horizontal transport

drive belt

Paper

Upper transport

roller (drive)

Upper transport

roller (driven)

Transport motor

(DC servomotor)

Transport drive belt

LCT transport sensor

End sensor bracket

Lock lever

Positioning bracket

Large Capacity Tray

1 July 1994

2-140

Содержание PCU10




































































































































































































Результаты поиска

Содержание PCU10

Отзывы:

Похожие инструкции для PCU10

Бренды по названию

Популярные бренды

Ricoh PCU10, Руководство по обучению обслуживанию

Результаты поиска

Содержание PCU10

Отзывы:

Похожие инструкции для PCU10

Бренды по названию

Популярные бренды