Ricoh PCU10 Скачать руководство пользователя страница 56

Страница: 56 / 195

2.2.4 Optical axis adjusting mechanism

The optical axis adjusting mechanism matches the angle

of the 1st mirror, lens, and 2nd mirror. The following

angles are adjusted:

•

Angle of the 1st mirror

•

Front and rear height of the 1st mirror housing

•

Angle of the 2nd mirror

•

Angle of the 1st mirror housing

Front and rear height of the 1st mirror housing

With the guide wire and double nut, adjust the front and

rear height of the 1st mirror housing.

Angle of the 1st mirror

Use the 1st mirror adjustment screws to adjust the 1st

mirror angle.

Angle of the 1st mirror housing

Use the guide eccentric cam to adjust the 1st mirror

housing angle (swings to the left and right).

Angle of the 2nd mirror

Use the 2nd mirror adjusting screw to adjust the angle of

the 2nd mirror.

CAUTION

•

Do not change the optical axis because it

can be adjusted only on the production line.

However, if the guide wire is loose, you may

take up the slack with the double nut.

Guide eccentric cam

1st mirror adjusting screws

1st mirror

housing

Guide wire

double nut

Guide wire

2nd mirror

adjusting screws

Optics

1 July 1994

2-20

Содержание PCU10




































































































































































































Результаты поиска

Содержание PCU10

Отзывы:

Похожие инструкции для PCU10

Бренды по названию

Популярные бренды

Ricoh PCU10, Руководство по обучению обслуживанию

Результаты поиска

Содержание PCU10

Отзывы:

Похожие инструкции для PCU10

Бренды по названию

Популярные бренды