Ricoh PCU10 Скачать руководство пользователя страница 55

Страница: 55 / 195

Mirror position correction

To change magnification, the lens shifts its imaging

position. The 1st and 2nd mirrors also shift to keep the

image in focus.
The 1st mirror is fastened to the 1st mirror housing and

moves along the 1st mirror guide rod and the grooves of

the housing guide.
The 2nd mirror is fastened to the 2nd mirror bracket.

The 2nd mirror interlocks with the 1st mirror housing and

is moved along the 2nd mirror guide rod and 2nd mirror

guide by the mirror drive cam.

Home position detection and magnification

The home position is full-size, and the magnification HP

sensor detects the home position.
When you turn ON the main switch, the mirror/lens

motor rotates, and the home position sensor actuator

passes through the magnification HP sensor.
When the motor reverses and the magnification HP

sensor is closed (blocked) by the home position sensor

actuator, the magnification motor stops.

1st mirror

1st

mirror

housing

1st mirror

guide rod

Mirror drive cam

2nd mirror guide rod

2nd mirror bracket

2nd mirror

2nd mirror guide

Housing guide

Magnification HP

sensor

E n l a r g e
direction

Magnification HP

sensor

Home

position

Home position

sensor actuator

Home position sensor

actuator (Fastened to the

1st mirror housing

Reduction

direction

1st mirror

housing

1 July 1994

Optics

2-19

Содержание PCU10




































































































































































































Результаты поиска

Содержание PCU10

Отзывы:

Похожие инструкции для PCU10

Бренды по названию

Популярные бренды

Ricoh PCU10, Руководство по обучению обслуживанию

Результаты поиска

Содержание PCU10

Отзывы:

Похожие инструкции для PCU10

Бренды по названию

Популярные бренды