Ricoh PCU10 Скачать руководство пользователя страница 142

Страница: 142 / 195

❈

7 During duplex paper feeding, transfer time from the

2nd duplex paper feed sensor turns ON to when the reg-

istration sensor turns ON is measured as for like the 1st

to 3rd tray paper feed. The feed motor ON timing for the

2nd time is changed.

2.13.11 Error reset

Problem:

Jogger fences error. The jogger HP sensor does not come ON within a fixed time.

Cause:

Fence overload, jogger HP sensor failure, jogger motor failure, connector contact failure.

Problem:

Back fence error. Back fence HP sensor does not come ON within a fixed time.

Cause:

Back fence overload, back fence HP sensor failure, back fence motor failure, connector

contact failure.

Duplex and Paper Exit

1 July 1994

2-106

Содержание PCU10




































































































































































































Результаты поиска

Содержание PCU10

Отзывы:

Похожие инструкции для PCU10

Бренды по названию

Популярные бренды

Ricoh PCU10, Руководство по обучению обслуживанию

Результаты поиска

Содержание PCU10

Отзывы:

Похожие инструкции для PCU10

Бренды по названию

Популярные бренды